Investigation of corrosion properties with Ni–P/TiNO coating on aluminum alloy bipolar plates in proton exchange membrane fuel cell

Aluminum alloy bipolar plates have unique application potential in proton exchange membrane fuel cell (PEMFC) due to the characteristics of lightweight and low cost. However, extreme susceptibility to corrosion in PEMFC operation condition limits the application. To promote the corrosion resistance of aluminum alloy bipolar plates, a Ni–P/TiNO coating was prepared by electroless plating and closed field unbalanced magnetron sputter ion plating (CFUMSIP) technology on the 6061 Al substrate. The research results show that Ni–P interlayer improves the deposition effect of TiNO outer layer and increase the content of TiN and TiO_xN_y phases. Compared to Ni–P and TiNO single-layer coatings, the Ni–P/TiNO coating samples exhibited the lowest current density value of (1.10 ± 0.02) × 10^?6 A·cm^?2 in simulated PEMFC cathode environment. Additionally, potential cyclic polarization measurements were carried out aiming to evaluate the durability of the aluminum alloy bipolar plate during the PEMFC start-up/shut-up process. The results illustrate that the Ni–P/TiNO coating samples exhibit excellent stability and corrosion resistance.     

Synergistic effect of co-alloying elements on site preferences and elastic properties of Ni3Al: A first-principles study

The site preferences of co-alloying elements (Mo–Ta, Mo–Re, Mo–Cr) in Ni₃Al are studied using first-principles calculations, and the effects of these alloying elements on the elastic properties of Ni₃Al are evaluated by elastic property calculations. The results show that the Mo–Ta, Mo–Re and Mo–Cr atom pairs all prefer Al–Al sites and the spatial neighbor relation of substitution sites almost has no influence on the site preference results. Furthermore, the Young's modulus of Ni₃Al increases much higher by substituting Al–Al sites with co-alloying atoms, among which Mo–Re has the best strengthening effect. The enhanced chemical bondings between alloying atoms and their neighbor host atoms are considered to be the main strengthening mechanism of the alloying elements in Ni₃Al.     

Abrasive waterjet micro-machining of channels in metals: Comparison between machining in air and submerged in water

Abrasive water jet technology can be used for micro-milling using recently developed miniaturized nozzles. Abrasive water jet (AWJ) machining is often used with both the nozzle tip and workpiece submerged in water to reduce noise and contain debris. This paper compares the performance of submerged and unsubmerged abrasive water jet micro-milling of channels in 316L stainless steel and 6061-T6 aluminum at various nozzle angles and standoff distances. The effect of submergence on the diameter and effective footprint of AWJ erosion footprints was measured and compared. It was found that the centerline erosion rate decreased with channel depth due to the spreading of the jet as the effective standoff distance increased, and because of the growing effect of stagnation as the channel became deeper. The erosive jet spread over a larger effective footprint in air than in water, since particles on the jet periphery were slowed much more quickly in water due to increased drag. As a result, the width of a channel machined in air was wider than that in water. Moreover, it was observed that the instantaneous erosion rate decreased with channel depth, and that this decrease was a function only of the channel cross-sectional geometry, being independent of the type of metal, the jet angle, the standoff distance, and regardless of whether the jet was submerged or in air, in either the forward or backward directions. It is shown that submerged AWJM results in narrower features than those produced while machining in air, without a decrease in centerline etch rate.     

Predicting the thermodynamics of aluminum dross denitrification of flue gas

Existing alumina extraction and material production methods result in the formation of harmful ammonia gas or ammonia water originating from aluminum nitride (AlN) in dross. Therefore, in this study, aluminum dross was used as a denitration reagent to eliminate nitrogen oxides in flue gas and AlN in dross. Based on the proposed scheme, thermodynamic calculations were performed to investigate the denitrification effect and reduction of aluminum dross in flue gas. The results show that equilibrium concentrations of NO, NO₂, and HF in the flue gas were influenced mainly by temperature; their concentrations increased with an increase in the temperature, reaching 4.4 × 10⁻²⁰, 1.7 × 10⁻³⁸, and 7.0 × 10⁻⁸ g/m³, respectively, at 923 K. The Gibbs free energy corresponding to the reaction of CO₂ with Al/AlN in aluminum dross was −377/–120 kJ/mol. HF, originating from the reaction of NaF and water vapor, maintained an extremely low concentration of 6.99 × 10⁻⁸ g/m³ at 923 K. These results indicate that aluminum dross processing may clean the flue gas and increase the calorific value while eliminating the hazards of AlN. The results obtained herein will provide theoretical guidance toward new avenues of aluminum dross utilization.     

Material design and development: From classical thermodynamics to CALPHAD and ICME approaches

This paper presents an overview and examples of material design and development using (1) classical thermodynamics; (2) CALPHAD (calculation of phase diagrams) modeling; and (3) Integrated Computational Materials Engineering (ICME) approaches. Although the examples are given in lightweight aluminum and magnesium alloys for structural applications, the fundamental methodology and modeling principles are applicable to all materials and engineering applications. The examples in this paper have demonstrated the effectiveness and limitations of classical thermodynamics in solving specific problems (such as nucleation during solidification and solid-state precipitation in aluminum alloys). Computational thermodynamics and CALPHAD modeling, when combined with critical experimental validation, have been used to guide the selection and design of new magnesium alloys for elevated-temperature applications. The future of material design and development will be based on a holistic ICME approach. However, key challenges exist in many aspects of ICME framework, such as the lack of diffusion/mobility databases for many materials systems, limitation of current microstructural modeling capability and integration tools for simulation codes of different length scales.     

Alloy optimisation of bainitic steel for large plastic mould

Based on the phase transformation theories, especially the T₀ concept of bainite transformation, alloy optimisation of bainitic steel with carbides has been carried out aiming at the produce of plastic mould with large cross-section. The effect of manganese and silicon on proeutectoid ferrite and bainite transformation is explored by dilatometric analysis, XRD and different microscopy techniques. The results show that after the alloy optimisation, the transformation of proeutectoid ferrite is suppressed and when the cooling rate is lower than 0·1°C?s^??1, the new lower bainite transformation appears by decreasing carbon capacity of austenite and promoting carbide precipitation. Industrial production proves that the optimised alloy SDP1 can meet the demand for the plastic mould with the thickness of 1050?mm.     

Growth behavior of aluminum borate whiskers on zirconia toughened alumina (ZTA) particle surface

In this work, B₄C-covered zirconia-toughened alumina (ZTA) particles are prepared and oxidised at 1050 °C for different times (0, 2, 4, and 8 h) in air. The X-ray diffraction and electron probe micro-analysis results show that the covering layer is mainly composed of oxide B₂O₃ intermetallics, residual B₄C particles, and Al₁₈B₄O₃₃ whiskers. The scanning electron microscopy results show that the growth of Al₁₈B₄O₃₃ whiskers on the ZTA particles enhances with increasing heat preservation time; the optimum holding time is determined to be 8 h Al₂O₃ in the ZTA particles diffuse into the covering layer and combine with B₂O₃ to form Al₁₈B₄O₃₃ whiskers; the Al₁₈B₄O₃₃ whiskers grow via the liquid-solid mechanism.     

Al-10Mg型固溶合金自然时效稳定性研究

测定了ZL30 5合金自然时效 33年的力学性能变化 ,观察了晶界的析出相 ,研究了组织和性能的关系 ,从而确定了ZL30 5合金具有长期自然时效稳定性。     

提高焊膏印刷质量的工艺改进

焊膏印刷作为SMT工艺的第一步，其质量好坏对SMT工艺有着重要影响。文章通过对焊膏成分、特性的分析，讨论了印刷中各种工艺参数的正确选择；对焊膏印刷中容易出现的质量问题进行了详细分析，指出了产生问题的原因，提出了改进措施。